Serving Johnson City, Kingsport & the Tri-Cities (423) 900-8254

Epoxy Calculator

423 Epoxy Pros provides the installed price ranges this calculator runs on, measured across Johnson City and the Tri-Cities. Enter your floor dimensions below for square footage, how much coating the job needs, and an installed price range by system. No email, nothing gated.

Square footage

440 sq ft

Coating needed

7.5–9 gal

Installed range

$1,760–$3,080

A planning range, not a quote. It assumes normal diamond-grind prep on a sound slab. Structural repair, moisture mitigation, or grinding off a failed previous coating are quoted separately once the floor has been seen. Coating needed is the mixed material for every coat of the chosen system, from a manufacturer’s published coverage rates (table below); the data sheet for the product actually used governs.

How much coating each system uses

A gallon of 100%-solids coating spread one mil thick covers about 1,604 square feet, so every coat’s coverage is set by how thick it goes on. A professional build is two or three coats, most of them 10 mils or more, which is why a whole system covers roughly 28 to 80 square feet per gallon, not the several hundred a thin one-coat floor paint lists. The rates below are from one manufacturer’s published system sheets, coat by coat. Another product line moves with its own film thickness; the arithmetic is the same.

System Coats (dry film) Sq ft per gallon, whole build 2-car garage (400–500 sq ft)
Solid-color epoxy basecoat 10–12 mils + topcoat 16–20 mils 50–62 6.5–10 gal
Flake (chip) epoxy basecoat 10–12 mils + topcoat 10.7–12 mils 68–77 5.5–7.5 gal
Polyaspartic system basecoat 10–10.7 mils + topcoat 10–10.7 mils 75–80 5–7 gal
Metallic epoxy basecoat 10–12 mils + metallic build coat 32–40 mils + topcoat 5 mils 28–34 12–18 gal

Sources (checked November 2026): Floorguard Products, Medium Duty Solid Industrial System sheet ; Floorguard Products, FGP Flake System sheet ; Floorguard Products, FGP Polyaspartic Flake System sheet ; Floorguard Products, Metallic Marble System sheet . The optional moisture primer (about 90 square feet per gallon), needed only on a slab that fails a moisture test, is not included. Flake systems also take about 0.13 pounds of flake per square foot broadcast to full coverage.

Per-square-foot pricing by system

These are the installed rates the calculator uses. They are the same numbers published in the Tri-Cities epoxy flooring cost guide, which explains what moves a job within its range.

  • Solid-color epoxy — $4 – $7 per square foot. One flat color with no broadcast on top. The lowest professional price, and the finish that shows every tire scuff and drift of pollen.
  • Flake (chip) epoxy — $5 – $10 per square foot. Colored vinyl chips scattered into the wet coat. The chips hide hairline cracks and patch marks, which matters on the older slabs common in Kingsport, Bristol and Elizabethton.
  • Polyaspartic system — $7 – $14 per square foot. Cures in hours instead of a day and does not yellow in sun. It also cures in cooler weather than epoxy, which widens the season here. Expect roughly 30 to 50 percent over a comparable epoxy job.
  • Metallic epoxy — $9 – $16 per square foot. Pearl-like pigment worked by hand into swirls while the coat is wet. You pay for the hours of hand work and the heavier pigment, not for a tougher floor.

Typical garage footprints

If you have not measured yet, these are the ranges most Tri-Cities garages fall into. Measure the slab rather than the building — the coating stops at the walls, and the door threshold is usually the shortest dimension.

  • 1-car garage — 240 to 300 square feet.
  • 2-car garage — 400 to 500 square feet.
  • 3-car garage — 600 to 750 square feet.

Frequently asked questions

How much epoxy do I need for a 2-car garage?
A typical 2-car garage is 400 to 500 square feet. A professional flake build (an epoxy basecoat and a clear polyaspartic topcoat, each about 10 to 12 mils) takes 5.5–7.5 gallons of mixed material. Solid color takes 6.5–10 gallons because its topcoat goes on thicker, and metallic takes 12–18 gallons because the metallic coat alone is 32 to 40 mils. These figures come from one manufacturer's published system sheets; the data sheet for the product actually used governs.
How accurate is this calculator?
It gives a planning range, not a quote. The two things it cannot see are the condition of your slab and how much prep it needs — a floor with a failing coating to grind off, or with cracks and spalling to repair, lands at the top of the range or above it. An on-site look is what turns a range into a number.
Does the price include concrete prep?
The ranges assume normal diamond-grind preparation on a sound slab, which installers build into the per-square-foot price. They do not include structural repair, moisture mitigation, or removing a failed previous coating. Those are quoted separately once the slab has been seen — see concrete repair and prep.

Ready for a real number instead of a range? Call (423) 900-8254 or pass your floor to a local installer.

Turn your estimate into a quote

Send the town, the square footage you entered and the coating you are leaning toward. A quote replaces the estimate once the slab has been seen.

Prefer to talk? Call (423) 900-8254

Thinking about coating your garage or shop floor?

Describe the floor and we pass it to an independent local installer in Johnson City, Kingsport, Bristol, or the surrounding Tri-Cities. Asking is free.

Call (423) 900-8254 · Floor Coating Help